|
|
装了BSD，始终启动不了X。
配置文件：/etc/X11/xorg.conf
# **********************************************************************
# Module section -- this section is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"
# This loads the DBE extension module.
Load "dbe" # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
SubSection "extmod"
Option "omit xfree86-dga" # don't initialise the DGA extension
EndSubSection
# This loads the font modules
Load "type1"
# Load "speedo"
Load "freetype"
# Load "xtt"
# This loads the GLX module
# Load "glx"
# This loads the DRI module
# Load "dri"
EndSection
# **********************************************************************
# Files section. This allows default font and rgb paths to be set
# **********************************************************************
Section "Files"
# The location of the RGB database. Note, this is the name of the
# file minus the extension (like ".txt" or ".db"). There is normally
# no need to change the default.
RgbPath "/usr/X11R6/lib/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#
FontPath "/usr/X11R6/lib/X11/fonts/misc/"
FontPath "/usr/X11R6/lib/X11/fonts/TTF/"
FontPath "/usr/X11R6/lib/X11/fonts/Type1/"
# FontPath "/usr/X11R6/lib/X11/fonts/CID/"
FontPath "/usr/X11R6/lib/X11/fonts/75dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/100dpi/"
FontPath "/usr/X11R6/lib/X11/fonts/local/"
# FontPath "/usr/X11R6/lib/X11/fonts/Speedo/"
# FontPath "/usr/X11R6/lib/X11/fonts/TrueType/"
# FontPath "/usr/X11R6/lib/X11/fonts/freefont/"
# The module search path. The default path is shown here.
# ModulePath "/usr/X11R6/lib/modules"
EndSection
# **********************************************************************
# Server flags section.
# **********************************************************************
Section "ServerFlags"
# Uncomment this to cause a core dump at the spot where a signal is
# received. This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
# Option "NoTrapSignals"
# Uncomment this to disable the <Ctrl><Alt><Fn> VT switch sequence
# (where n is 1 through 12). This allows clients to receive these key
# events.
# Option "DontVTSwitch"
# Uncomment this to disable the <Ctrl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
# Option "DontZap"
# Uncomment this to disable the <Ctrl><Alt><KP_+>/<KP_-> mode switching
# sequences. This allows clients to receive these key events.
# Option "Dont Zoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
# Option "DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
# Option "AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
# Option "DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
# Option "AllowNonLocalModInDev"
EndSection
*******省略了鼠标键盘的部分***************
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
Section "Monitor"
Identifier "Monitor"
# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
HorizSync 31.5, 35.15, 35.5
# HorizSync 30-64 # multisync
# HorizSync 31.5, 35.2 # multiple fixed sync frequencies
# HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
VertRefresh 50-70
EndSection
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
Section "Device"
Identifier "Standard VGA"
VendorName "Unknown"
BoardName "Unknown"
# The chipset line is optional in most cases. It can be used to override
# the driver's chipset detection, and should not normally be specified.
# Chipset "generic"
# The Driver line must be present. When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module. Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
Driver "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for. When this line isn't present, a device
# section can only match up with the primary video device. For PCI
# devices a line like the following could be used. This line should not
# normally be included unless there is more than one video device
# intalled.
# BusID " CI:0:10:0"
# VideoRam 256
# Clocks 25.2 28.3
EndSection
# Device configured by xorgconfig:
Section "Device"
Identifier "Video-card"
Driver "chips"
#VideoRam 32768
# Option "suspend_hack"
# Option "STN"
# Option "no_stretch"
# Option "no_center"
# Option "use_modeline"
# Option "fix_panel_size"
# videoram 512
# Option "noaccel"
# Option "no_bitblt"
# Option "xaa_no_color_exp"
# Option "xaa_benchmark"
# Option "hw_cursor"
# Option "nolinear"
# MemBase 0x03b00000
# Option "hw_clocks"
# Textclockfreq 25.175
# Insert Clocks lines here if appropriate
EndSection
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present. Each describes
# the configuration of a single screen. A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
Identifier "Screen 1"
Device "Video-card"
Monitor "Monitor"
DefaultDepth 24
Subsection "Display"
Depth 8
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 16
Modes "1280x1024" "1024x768" "800x600" "640x480"
ViewPort 0 0
EndSubsection
Subsection "Display"
Depth 24
Modes "1024x768"
ViewPort 0 0
EndSubsection
EndSection
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present. Each describes
# the way multiple screens are organised. A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option. In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
Section "ServerLayout"
# The Identifier line must be present
Identifier "Simple Layout"
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens. The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen. In this example, screen 2 is located to the
# right of screen 1.
Screen "Screen 1"
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used. Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
InputDevice "Mouse1" "CorePointer"
InputDevice "Keyboard1" "CoreKeyboard"
EndSection
# Section "DRI"
# Mode 0666
# EndSection
这个是日志：
/var/log/X11/xorg.0.log
X Window System Version 6.9.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 6.9
Build Operating System: FreeBSD 6.1 i386 [ELF]
Current Operating System: FreeBSD BirdSky.UnixWorld 6.1-RELEASE FreeBSD 6.1-RELEASE #0: Sun May 7 04:42:56 UTC 2006 root@opus.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP i386
Build Date: 24 March 2006
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Fri Oct 27 19:24:10 2006
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "Monitor"
(**) | |-->Device "Video-card"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(WW) `fonts.dir' not found (or not valid) in "/usr/X11R6/lib/X11/fonts/local/".
Entry deleted from font path.
(Run 'mkfontdir' on "/usr/X11R6/lib/X11/fonts/local/").
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/TTF/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(WW) checkDevMem: failed to open /dev/mem (Operation not permitted)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.8
X.Org XInput driver : 0.5
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on freebsd
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.so
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(--) Using syscons driver with X support (version 2.0)
(--) using VT number 9
(WW) xf86EnableIO: Failed to open /dev/io for extended I/O(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX(B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MXE(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX
(II) LoadModule: "dbe"
(II) Loading /usr/X11R6/lib/modules/extensions/libdbe.so
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.9.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "chips"
(II) Loading /usr/X11R6/lib/modules/drivers/chips_drv.so
(II) Module chips: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.1
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "kbd"
(II) Loading /usr/X11R6/lib/modules/input/kbd_drv.so
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.1
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) CHIPS: Driver for Chips and Technologies chipsets: ct65520, ct65525,
ct65530, ct65535, ct65540, ct65545, ct65546, ct65548, ct65550,
ct65554, ct65555, ct68554, ct69000, ct69030, ct64200, ct64300
(WW) xf86EnableIO: Failed to open /dev/io for extended I/O(EE) No devices detected.
Fatal server error:
no screens found
Please consult the The X.Org Foundation support
at http://wiki.X.Org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.
这是我SUSE中的配置文件：
Section "Monitor"
HorizSync 28-60
Identifier "Monitor[0]"
ModelName "1024X768@60HZ"
Option "DPMS"
VendorName "--> LCD"
VertRefresh 30-60
UseModes "Modes[0]"
EndSection
Section "Modes"
Identifier "Modes[0]"
Modeline "1024x600" 47.26 1024 1064 1168 1312 600 601 604 621
Modeline "800x600" 36.88 800 832 912 1024 600 601 604 621
Modeline "768x576" 33.74 768 792 872 976 576 577 580 596
Modeline "640x480" 23.06 640 656 720 800 480 481 484 497
Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806
EndSection
Section "Screen"
DefaultDepth 24
SubSection "Display"
Depth 15
Modes "1024x768" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 16
Modes "1024x768" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "1024x768" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 32
Modes "1024x768" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
SubSection "Display"
Depth 8
Modes "1024x768" "1024x600" "800x600" "768x576" "640x480"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
Section "Device"
BoardName "SiS 660"
BusID "1:0:0"
Driver "sis"
Identifier "Device[0]"
Option "EnableSiSCtrl" "on"
VendorName "SiS"
EndSection
Section "ServerLayout"
Identifier "Layout[all]"
InputDevice "Keyboard[0]" "CoreKeyboard"
InputDevice "Mouse[1]" "CorePointer"
InputDevice "Mouse[3]" "SendCoreEvents"
Option "Clone" "off"
Option "Xinerama" "off"
Screen "Screen[0]"
EndSection
Section "DRI"
Group "video"
Mode 0660
EndSection
Section "Extensions"
EndSection
我不知道怎么回事，高手指教了！ |
|
IP卡
狗仔卡
发表于 2006-10-27 12:10:32
提升卡
置顶卡
沉默卡
喧嚣卡
变色卡
显身卡
楼主