|
|
楼主 |
发表于 2006-8-21 18:57:42
|
显示全部楼层
OK，信息如下：
(II) I810: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100,
(**) I810(0): Depth 24, (--) framebuffer bpp 32
(==) I810(0): RGB weight 888
(==) I810(0): Default visual is TrueColor
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): VESA VBE Version 3.0
(II) I810(0): VESA VBE Total Mem: 7872 kB
(II) I810(0): VESA VBE OEM: Intel(r)Lakeport-G Graphics Chip Accelerated VGA BIOS
(II) I810(0): VESA VBE OEM Software Rev: 1.0
(II) I810(0): VESA VBE OEM Vendor: Intel Corporation
(II) I810(0): VESA VBE OEM Product: Intel(r)Lakeport-G Graphics Controller
(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(II) I810(0): Integrated Graphics Chipset: Intel(R) 945G
(--) I810(0): Chipset: "945G"
(--) I810(0): Linear framebuffer at 0xD0000000
(--) I810(0): IO registers at addr 0xE2000000
(II) I810(0): 2 display pipes available.
(II) I810(0): detected 7932 kB stolen memory.
(WW) I810(0): /dev/agpgart is either not available, or no memory is available
(WW) I810(0): VideoRAM reduced to 7932 kByte (limited to available sysmem)
(--) I810(0): Pre-allocated VideoRAM: 7932 kByte
(--) I810(0): VideoRAM: 7932 kByte
(==) I810(0): video overlay key set to 0x101fe
(**) I810(0): page flipping disabled
(==) I810(0): Using gamma correction (1.0, 1.0, 1.0)
(II) I810(0): BIOS Build: 1215
(==) I810(0): Device Presence: disabled.
(==) I810(0): Display Info: enabled.
(II) I810(0): Broken BIOSes cause the system to hang here.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(WW) I810(0): Extended BIOS function 0x5f64 not supported.
(II) I810(0): Currently active displays on Pipe A:
(II) I810(0): CRT
(II) I810(0): No active displays on Pipe B.
(==) I810(0): Display is using Pipe A
(--) I810(0): HW Cursor disabled because it needs agpgart memory.
(--) I810(0): Maximum frambuffer space: 7784 kByte
(II) I810(0): VESA VBE DDC supported
(II) I810(0): VESA VBE DDC Level 2
(II) I810(0): VESA VBE DDC transfer in appr. 1 sec.
(II) I810(0): VESA VBE DDC read failed
(II) I810(0): Will use BIOS call 0x5f05 to set refresh rates for CRTs.
(--) I810(0): Maximum space available for video modes: 7784 kByte
(II) I810(0): My Monitor: Using hsync range of 31.50-75.50 kHz
(II) I810(0): My Monitor: Using vrefresh range of 50.00-120.00 Hz
(II) I810(0): Not using built-in mode "1600x1200" (width too large for virtual size)
(II) I810(0): Not using built-in mode "1280x1024" (width too large for virtual size)
(II) I810(0): 7656 kBytes additional video memory is required to
(II) I810(0): 5608 kBytes additional video memory is required to enable DRI.
(II) I810(0): Disabling DRI.
(--) I810(0): Virtual size is 1024x768 (pitch 1024)
(**) I810(0): *Built-in mode "1024x768"
(**) I810(0): Built-in mode "800x600"
(**) I810(0): Built-in mode "640x480"
(II) I810(0): Attempting to use 85.00Hz refresh for mode "1024x768" (854)
(II) I810(0): Attempting to use 85.14Hz refresh for mode "800x600" (852)
(II) I810(0): Attempting to use 85.01Hz refresh for mode "640x480" (850)
(==) I810(0): DPI set to (75, 75)
(==) I810(0): VBE Restore workaround: enabled.
(II) I810(0): initializing int10
(WW) I810(0): Bad V_BIOS checksum
(II) I810(0): Primary V_BIOS segment is: 0xc000
(II) I810(0): VESA BIOS detected
(II) I810(0): VESA VBE Version 3.0
(II) I810(0): VESA VBE Total Mem: 7872 kB
(II) I810(0): VESA VBE OEM: Intel(r)Lakeport-G Graphics Chip Accelerated VGA BIOS
(II) I810(0): VESA VBE OEM Software Rev: 1.0
(II) I810(0): VESA VBE OEM Vendor: Intel Corporation
(II) I810(0): VESA VBE OEM Product: Intel(r)Lakeport-G Graphics Controller
(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0
(--) I810(0): Xv is disabled because it needs 2D accel and AGPGART.
(II) I810(0): Allocated 128 kB for the ring buffer at 0x0
(II) I810(0): Allocating at least 512 scanlines for pixmap cache
(II) I810(0): Initial framebuffer allocation size: 6144 kByte
(II) I810(0): Allocated 64 kB for the scratch buffer at 0x7af000
(II) I810(0): 0x81ee9b8: Memory at offset 0x00020000, size 6144 kBytes
(II) I810(0): 0x81ef2f0: Memory at offset 0x00000000, size 0 kBytes
(II) I810(0): 0x81ef318: Memory at offset 0x00000000, size 0 kBytes
(II) I810(0): 0x81ef344: Memory at offset 0x00000000, size 128 kBytes
(II) I810(0): 0x81ee9f8: Memory at offset 0x007af000, size 64 kBytes
(==) I810(0): Write-combining range (0xd0000000,0x10000000)
(II) I810(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp-> IOOffset is 0x0000
(WW) I810(0): Extended BIOS function 0x5f05 not supported.
(II) I810(0): BIOS call 0x5f05 not supported, setting refresh with VBE 3 method.(II) I810(0): Setting refresh with VBE 3 method.
(II) I810(0): Display plane A is enabled and connected to Pipe A.
(II) I810(0): Display plane B is disabled and connected to Pipe B.
(II) I810(0): Enabling plane A.
(II) I810(0): Display plane A is now enabled and connected to Pipe A.
(II) I810(0): Display plane B is now disabled and connected to Pipe B.
(II) I810(0): PIPEACONF is 0x80000000
(II) I810(0): PIPEBCONF is 0x80000000
(II) I810(0): Mode bandwidth is 47 Mpixel/s
(WW) I810(0): Extended BIOS function 0x5f28 not supported.
(II) I810(0): Using XFree86 Acceleration Architecture (XAA)
(==) I810(0): Backing store disabled
(==) I810(0): Silken mouse enabled
(II) I810(0): Initializing SW Cursor!
(II) I810(0): direct rendering: Disabled
(II) I810(0): RandR enabled, ignore the following RandR disabled message.
(II) I810(0): Rotating to 0 degrees |
|
IP卡
狗仔卡
发表于 2006-8-19 17:53:33
显身卡