配置XFREE86出错

hmglll

root:/dev# cd ~
root:~# XFree86 -configure
_XSERVTransSocketINETCreateListener: ...SocketCreateListener() failed
_XSERVTransMakeAllCOTSServerListeners: server already running

Fatal server error:
Cannot establish any listening sockets - Make sure an X server isn't already run
ning

When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to xfree86@xfree86.org.

doooom

直接运行xf86config怎么样？我一般都用这个。生成XF86config文档之后再手动编辑。

hmglll

As with most libraries, there is no configuration to do, save that the library directory i.e. /usr/lib or /usr/local/lib should appear in /etc/ld.so.conf so that ldd can find the shared libraries. After checking that this is the case, /sbin/ldconfig should be run whilst logged in as root.

tram

这是让你把/usr/lib和/usr/local/lib加到/etc/ld.so.conf里，再用root的用户来运行/sbin/ldconfig，这样做，就可以让你安装的库文件被其它的程序找到。

hmglll

两位兄弟 ，还是不行啊！
我工作过程如下：
1安操作说明安装XC包(补丁了TRAM包)，安装成功，没有错误发生；
2运行xf86config进行配置；
3按配置说明进行配置；
4创建 XF86Config 文件；
后附过程：
root:~# ldconfig
root:~# source ~/.bash_profile
root:~# cd /dev
root:/dev# ln -s psaux mouse
ln: `mouse': File exists
root:/dev#       cd ~
root:~# XFree86 -configure
_XSERVTransSocketINETCreateListener: ...SocketCreateListener() failed
_XSERVTransMakeAllCOTSServerListeners: server already running

Fatal server error:
Cannot establish any listening sockets - Make sure an X server isn't already running

When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to xfree86@xfree86.org.

root:~#       XFree86 -xf86config ~/XF86Config.new
_XSERVTransSocketINETCreateListener: ...SocketCreateListener() failed
_XSERVTransMakeAllCOTSServerListeners: server already running

Fatal server error:
Cannot establish any listening sockets - Make sure an X server isn't already running

When reporting a problem related to a server crash, please send
the full server output, not just the last messages.
This can be found in the log file "/var/log/XFree86.0.log".
Please report problems to xfree86@xfree86.org.

hmglll

我的LFS内核版本与RH的不一样，RH的是2.4.8-18 8.0

hmglll

有用吗？

hmglll

到了LFS下，我进行以上的第四步4创建 XF86Config 文件：
#：cd ~
#：XFree86 -configure
      
很顺利地通过(出现黑幕但没有听见咔塔声)，继续第五步测试系统
#：XFree86 -xf86config ~/XF86Config.new
花屏，分别率设置太高了！
各位，是否是在虚拟环境下不能这样做还是什么原因？？
如何设置分辩率(不想翻书了)

doooom

这个，运行了xf86config之后还要XFree86 -config么？我想这个时候已经有了。XF86config这个文件了。修改这个文件的最后部分(把你显示器上不去的分辨率山掉。还有就是前面的刷新率 在monitor那个部分里面。改小。直接启动X，应该可以。

hmglll

按教程是要做这些配置的啊
还有些我没有做呢？