官方源没有 kernel26-scsi 了!?????

athlon_r

升级了 一下kernel
也没有仔细看 直接一路 y/enter 过去...... - -!
后发现 不是scsi的了......  我的soft raid 用不了了........
看了一下 2.6.14 指定initrd.img 也不支持我的soft raid  无奈降回2.6.13-scsi

athlon_r

难到就我一个 用 scsi内核???!!!....

刚才 无聊 pacman -Ss star .....
发现.....

1. extra/stardict 2.4.5-1
2.     StarDict is a powerful international dictionary written in Gtk2.

复制代码

... 悍然..........
好吧 我承认2005. 6~12 我有6个月的 linux使用真空期

diony

Post by athlon_r
难到就我一个 用 scsi内核???!!!....

刚才 无聊 pacman -Ss star .....
发现.....

1. extra/stardict 2.4.5-1
   
2.     StarDict is a powerful international dictionary written in Gtk2.
   

复制代码

... 悍然..........
好吧 我承认2005. 6~12 我有6个月的 linux使用真空期

咱俩的真空期差不多。

休想

楼上的，的确消失了一段时间的说

mingfal

好象是说现在用initrd了，所以没有ide和scsi之分了。

athlon_r

Post by mingfal
好象是说现在用initrd了，所以没有ide和scsi之分了。

关键是用了initrd.img 也不能识别我的software raid .....

Arne

试过full的那一个吗？

athlon_r

Post by Arne
试过full的那一个吗？

当然试过... 好象不支持soft raid

threedot

Post by athlon_r
当然试过... 好象不支持soft raid

yes,in my computer,sata harddisk can't work!

diony

看看这个连接：
http://wiki.archlinux.org/index.php/Initrd

其中我认为会对你有帮助的有:

[size=+1]Changes for RAID users

Now that we boot through an initrd, RAID users will need to do some extra configuration. First, the initrd needs to know which devices are in your root array. Previously, RAID support was built-in to the kernel, so we could take advantage of the autodetection magic that happens in there. But now that RAID is modular, the autodetection does not work. Hence this extra step.

1. Edit /etc/mkinitrd.conf and add the proper RAID settings for your root array. In this example, /dev/hda3 and /dev/hdc3 are part of the root array. (If you don't use RAID on your root array, skip this step)

1. 
   
2. # If you use software RAID for your root device then list all the devices
   
3. # that belong to your root array here.  If your root RAID device is
   
4. # something other than md0, then change the RAID_ROOT_ARRAY setting.
   
5. #    eg, RAID_ROOT_DEVICES="/dev/hda3 /dev/hdc3"
   
6. RAID_ROOT_ARRAY="md0"
   
7. RAID_ROOT_DEVICES="/dev/hda3 /dev/hdc3"
   

复制代码

2. Store your current RAID setup in /etc/mdadm.conf. This is quickly done with the following command:

1. 
   
2. # mdadm -D --scan >>/etc/mdadm.conf
   

复制代码

You should probably look at /etc/mdadm.conf and make sure the proper ARRAY lines showed up at the bottom. Also make sure you have a line in there that says DEVICE partitions. This is crucial. It's also in Arch's default mdadm.conf, so most of you should have it.

3. Now regenerate the init ramdisk.

1. 
   
2. # mkinitrd auto

复制代码

You're good to go!

去看看那个wiki吧，应该有用。